Analog Devices Blackfin ADSP-BF537 Hardware Reference Manual Download

Page: 768 / 1218

SPORT Registers

12-48

ADSP-BF537 Blackfin Processor Hardware Reference

When the SPORT is enabled to transmit (

TSPEN

set), corresponding

SPORT configuration register writes are not allowed except for

SPORTx_TCLKDIV

and multichannel mode channel select registers. Writes to

disallowed registers have no effect. While the SPORT is enabled,

SPORTx_TCR1

is not written except for bit 0 (

TSPEN

). For example:

write (SPORTx_TCR1, 0x0001) ;

/* SPORT TX Enabled */

write (SPORTx_TCR1, 0xFF01) ;

/* ignored, no effect */

write (SPORTx_TCR1, 0xFFF0) ;

/* SPORT disabled, SPORTx_TCR1

still equal to 0x0000 */

Figure 12-25. SPORTx Transmit Configuration 1 Register

15 14

13 12 11 10

SPORTx Transmit Configuration 1 Register (SPORTx_TCR1)

0 - Transmit disabled
1 - Transmit enabled

ITFS (Internal Transmit
Frame Sync Select)

ITCLK (Internal Transmit
Clock Select)

TDTYPE[1:0] (Data Format-
ting Type Select)

TLSBIT (Transmit Bit Order)

TSPEN (Transmit Enable)

LTFS (Low Transmit
Frame Sync Select)

LATFS (Late Transmit
Frame Sync)
0 - Early frame syncs
1 - Late frame syncs

TCKFE (Clock Falling
Edge Select)

0 -External transmit clock

selected

1 - Internal transmit clock

selected

00 - Normal operation
01 - Reserved
10 - Compand using

-law

11 - Compand using A-law

0 - Transmit MSB first
1 - Transmit LSB first

Reset = 0x0000

0 - External TFS used
1 - Internal TFS used

0 - Drive data and internal

frame syncs with rising
edge of TSCLK. Sample
external frame syncs with
falling edge of TSCLK.

1 - Drive data and internal

frame syncs with falling
edge of TSCLK. Sample
external frame syncs
with rising edge of TSCLK.

0 - Active high TFS
1 - Active low TFS

TFSR (Transmit Frame Sync
Required Select)

DITFS (Data-Independent
Transmit Frame Sync Select)
0 - Data-dependent TFS generated
1 - Data-independent TFS generated

0 - Does not require TFS for

every data word

1 - Requires TFS for every

data word

SPORT0:

0xFFC0 0800

SPORT1:

0xFFC0 0900

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Blackfin ADSP-BF537

Reviews:

Related manuals for Blackfin ADSP-BF537

Brands by name

Popular brands

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

Search results

Summary of Contents for Blackfin ADSP-BF537

Reviews:

Related manuals for Blackfin ADSP-BF537

Brands by name

Popular brands