manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

Functional Description

5-52

ADSP-BF537 Blackfin Processor Hardware Reference

 

If two MDMA streams are used (S0-D0 and S1-D1), the user may choose 
to allocate bandwidth either by fixed stream priority or by a round robin 
scheme. This is selected by programming the 

MDMA_ROUND_ROBIN_PERIOD

 

field in the 

DMA_TC_PER

 register (see 

“Static Channel Prioritization” on 

page 5-48

).

If this field is set to 0, then MDMA is scheduled by fixed priority. 
MDMA stream 0 takes precedence over MDMA stream 1 whenever 
stream 0 is ready to perform transfers. Since an MDMA stream is typically 
capable of transferring data on every available cycle, this could cause 
MDMA stream 1 traffic to be delayed for an indefinite time until any and 
all MDMA stream 0 operations are complete. This scheme could be 
appropriate in systems where low duration but latency sensitive data buff-
ers need to be moved immediately, interrupting long duration, low 
priority background transfers.

If the 

MDMA_ROUND_ROBIN_PERIOD

 field is set to some nonzero value in the 

range 

1 <= P <= 31

, then a round robin scheduling method is used. The 

two MDMA streams are granted bus access in alternation in bursts of up 
to 

P

 data transfers. This could be used in systems where two transfer pro-

cesses need to coexist, each with a guaranteed fraction of the available 
bandwidth. For example, one stream might be programmed for inter-
nal-to-external moves while the other is programmed for 
external-to-internal moves, and each would be allocated approximately 
equal data bandwidth.

In round robin operation, the MDMA stream selection at any time is 
either “free” or “locked.” Initially, the selection is free. On any free cycle 
available to MDMA (when no peripheral DMA accesses take precedence), 
if either or both MDMA streams request access, the higher precedence 
stream will be granted (stream 0 in case of conflict), and that stream’s 
selection is then “locked.” The 

MDMA_ROUND_ROBIN_COUNT

 counter field in 

the 

DMA_TC_CNT

 register is loaded with the period 

P

 from 

MDMA_ROUND_

ROBIN_PERIOD

, and MDMA transfers begin. The counter is decremented 

on every data transfer (as each data word is written to memory). After the 

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
Neo Instruments Mini Vent User Manual preview
Mini Vent
Brand: Neo Instruments Pages: 2
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
Cypress Semiconductor CY7C68033 Specification Sheet preview
CY7C68033
Brand: Cypress Semiconductor Pages: 33
Kontron CP3002-RA User Manual preview
CP3002-RA
Brand: Kontron Pages: 98
Idis DR-1204P Installation Manual preview
DR-1204P
Brand: Idis Pages: 22
Harman crown PIP Series Reference Manual preview
crown PIP Series
Brand: Harman Pages: 16
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Brand: Ubiquiti Pages: 24
Tripp Lite SmartRack SR25UBEXP Specifications preview
SmartRack SR25UBEXP
Brand: Tripp Lite Pages: 4
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Brand: Barracuda Pages: 8
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Brand: Ebyte Pages: 23
Kordis NCB210X2-DS-AB Datasheet preview
NCB210X2-DS-AB
Brand: Kordis Pages: 31
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Brand: Arctic Pages: 7

Brands by name

Popular brands

Load more brands