manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

Description of Operation

8-16

ADSP-BF537 Blackfin Processor Hardware Reference

 

Discarded Frames

Frames that fail the address filter are discarded immediately after the desti-
nation address is received, and neither their data nor their status values are 
written to memory via DMA. Frames that pass the address filter but fail 
the frame filter before 32 bytes are received are also discarded immedi-
ately. Once at least 32 bytes of a frame have been received, and if the 
address and frame filters both pass, the MAC begins to write the frame to 
memory via DMA RX.

Aborted Frames

Frames that fail the frame filter after 32 bytes have been received are 
aborted. The MAC issues a restart DMA control command, causing the 
current RX data DMA descriptor to be reinitialized with its starting 
address and counts. The aborted frame’s status is not written to memory. 
Instead, the current DMA data and status buffers are recycled for the next 
RX frame. For all frames that pass both the address and frame filters, both 
data and status are written to memory via DMA.

Control Frames

If the 

FLCE

 (flow control enable) bit is set, MAC control frames (with the 

control type 88-08) whose DAs match either the station MAC address 
(with inverse filtering disabled) or the global pause multicast address will 
pass the address filter, and thus may also have status of receiveOK. If the 
frame also is a supported pause control frame (with length = 64 bytes, and 
opcode = pause = 00-01, and in full-duplex mode), then the frame filter 
condition is determined by the 

PCF

 (pass control frames) bit. If the frame 

is not also a supported pause control frame, then it is in error, and its 
frame filter condition depends on the 

PBF

 (pass bad frames) bit.

Examples

• To perform standard IEEE-802.3 filtering, clear the operating 

mode register bits 

HU

, 

PR

, 

IFE

, 

DBF

, 

PBF

, and 

PSF

. With these selec-

tions, the Ethernet MAC accepts error-free broadcast frames and 

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

3Com 3CRSHPW196 User Manual preview
3CRSHPW196
Brand: 3Com Pages: 16
Compaq Proliant 800 Setup And Installation Manual preview
Proliant 800
Brand: Compaq Pages: 112
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Brand: JUMO Pages: 41
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Brand: HighPoint Pages: 17
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
Ampro Corporation LITTLE BOARD P5X Hardware User Manual preview
LITTLE BOARD P5X
Brand: Ampro Corporation Pages: 121
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Brand: Corsair Pages: 30
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Brand: Intel Pages: 28
LevelOne ServCon FPS-3003 Quick Install Manual preview
ServCon FPS-3003
Brand: LevelOne Pages: 45
Hawking WIRELESS-G CARDBUS PC CARD - GUIDE D User Manual preview
WIRELESS-G CARDBUS PC CARD - GUIDE D
Brand: Hawking Pages: 26
TRENDnet TEW-221PC User Manual preview
TEW-221PC
Brand: TRENDnet Pages: 56
RadiSys ES4001G ONT Quick Installation Manual preview
ES4001G ONT
Brand: RadiSys Pages: 6
Linksys EFG20 User Manual preview
EFG20
Brand: Linksys Pages: 37
Omron CJ1W-CRM21 Operation Manual preview
CJ1W-CRM21
Brand: Omron Pages: 172

Brands by name

Popular brands

Load more brands