manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

ADSP-BF537 Blackfin Processor Hardware Reference

12-11 

 

SPORT Controllers

A processor reset disables the SPORTs by clearing the 

SPORTx_TCR1

, 

SPORTx_TCR2

, 

SPORTx_RCR1

, and 

SPORTx_RCR2

 registers (including the 

TSPEN

 and 

RSPEN 

enable bits) and the 

SPORTx_TCLKDIV

, 

SPORTx_RCLKDIV

, 

SPORTx_TFSDIVx

, and 

SPORTx_RFSDIVx

 clock and frame sync divisor regis-

ters. Any ongoing operations are aborted.

Clearing the 

TSPEN

 and 

RSPEN

 enable bits disables the SPORTs and aborts 

any ongoing operations. Status bits are also cleared. Configuration bits 
remain unaffected and can be read by the software in order to be altered or 
overwritten. To disable the SPORT output clock, set the SPORT to be 
disabled. 

L

Note that disabling a SPORT via 

TSPEN

/

RSPEN

 may shorten any 

currently active pulses on the 

TFSx

/

RFSx

 and 

TSCLKx

/

RSCLKx

 out-

puts, if these signals are configured to be generated internally.

The SPORTs are ready to start transmitting or receiving data no later than 
three serial clock cycles after they are enabled in the 

SPORTx_TCR1

 or 

SPORTx_RCR1

 register. No serial clock cycles are lost from this point on. 

The first internal frame sync will occur one frame sync delay after the 
SPORTs are ready. External frame syncs can occur as soon as the SPORT 
is ready.

When disabling the SPORT from multichannel operation, first disable 

TXEN

 and then disable 

RXEN

. Note both 

TXEN

 and 

RXEN

 must be disabled 

before reenabling. Disabling only TX or RX is not allowed.

Setting SPORT Modes

SPORT configuration is accomplished by setting bit and field values in 
configuration registers. Each SPORT must be configured prior to being 
enabled. Once the SPORT is enabled, further writes to the SPORT con-
figuration registers are disabled (except for 

SPORTx_RCLKDIV

, 

SPORTx_TCLKDIV

, and multichannel mode channel select registers). To 

change values in all other SPORT configuration registers, disable the 
SPORT by clearing 

TSPEN

 in 

SPORTx_TCR1

 and/or 

RSPEN

 in 

SPORTx_RCR1

.

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

3Com 3C3FE574BT Quick Start Manual preview
3C3FE574BT
Brand: 3Com Pages: 8
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
ETAS ES1392.1 User Manual preview
ES1392.1
Brand: ETAS Pages: 36
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4
EVGA inDtube Instructions preview
inDtube
Brand: EVGA Pages: 3
SilverStone SDP12 Quick Start Manual preview
SDP12
Brand: SilverStone Pages: 2
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Brand: Allied Telesis Pages: 44
LevelOne CamCon FCS-4000 User Manual preview
CamCon FCS-4000
Brand: LevelOne Pages: 94
National Datacomm 9210S01 User Manual preview
9210S01
Brand: National Datacomm Pages: 62
3Ware 9500S-8 - Escalade RAID Controller User Manual preview
9500S-8 - Escalade RAID Controller
Brand: 3Ware Pages: 46
National Instruments Texas Instruments 6711 DSK Quick Start Manual preview
Texas Instruments 6711 DSK
Brand: National Instruments Pages: 2
Waveshare OPS-I5-1135G7 User Manual preview
OPS-I5-1135G7
Brand: Waveshare Pages: 23
Omron G3PB Manual preview
G3PB
Brand: Omron Pages: 8

Brands by name

Popular brands

Load more brands