manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

ADSP-BF537 Blackfin Processor Hardware Reference

10-19 

 

SPI Compatible Port Controllers

transaction is initiated by enabling the SPI for DMA receive mode. Subse-
quent individual transactions are initiated by a DMA read of the 

SPI_RDBR

. A value of 11 selects DMA transmit mode and the transaction is 

initiated by a DMA write of the 

SPI_TDBR

.

The 

PSSE

 bit is used to enable the 

SPISS

 input for master. When not used, 

SPISS

 can be disabled, freeing up a chip pin as general-purpose I/O. 

The 

EMISO

 bit enables the 

MISO

 pin as an output. This is needed in an 

environment where the master wishes to transmit to various slaves at one 
time (broadcast). Only one slave is allowed to transmit data back to the 
master. Except for the slave from whom the master wishes to receive, all 
other slaves should have this bit cleared.

The 

SPE

 and 

MSTR

 bits can be modified by hardware when the 

MODF

 bit of 

the 

SPI_STAT

 register is set. See 

“Mode Fault Error (MODF)” on 

page 10-21

.

Figure 10-12 on page 10-41

 provides the bit descriptions for 

SPI_CTL

.

Clock Signals

The 

SCK

 signal is a gated clock that is only active during data transfers for 

the duration of the transferred word. The number of active edges is equal 
to the number of bits driven on the data lines. The clock rate can be as 
high as one-fourth of the 

SCLK

 rate. For master devices, the clock rate is 

determined by the 16-bit value of 

SPI_BAUD

. For slave devices, the value in 

SPI_BAUD

 is ignored. When the SPI device is a master, 

SCK

 is an output sig-

nal. When the SPI is a slave, 

SCK

 is an input signal. Slave devices ignore 

the serial clock if the slave select input is driven inactive (high).

The 

SCK

 signal is used to shift out and shift in the data driven onto the 

MISO

 and 

MOSI

 lines. The data is always shifted out on one edge of the 

clock (the active edge) and sampled on the opposite edge of the clock (the 
sampling edge). Clock polarity and clock phase relative to data are pro-
grammable into 

SPI_CTL

 and define the transfer format.

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

Vanguard 342 Quick Reference Manual preview
342
Brand: Vanguard Pages: 4
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
Roland MSL-15 Owner'S Manual preview
MSL-15
Brand: Roland Pages: 12
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Brand: Longshine Pages: 27
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
Wyse C90LE7 Quick Start Manual preview
C90LE7
Brand: Wyse Pages: 8
Supermicro X12SPO-NTF/-F User Manual preview
X12SPO-NTF/-F
Brand: Supermicro Pages: 131
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
National Instruments PCI-6601 User Manual preview
PCI-6601
Brand: National Instruments Pages: 52
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Brand: Multiplex Pages: 10
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
DigiTech RP 3 User Manual preview
RP 3
Brand: DigiTech Pages: 28
LevelOne NVR-0432 User Manual preview
NVR-0432
Brand: LevelOne Pages: 142
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
Abocom WM5504 User Manual preview
WM5504
Brand: Abocom Pages: 70
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Brand: Hanwha Techwin Pages: 88

Brands by name

Popular brands

Load more brands