Amsco Century Operator'S Manual Download Page 7

Page: 7 / 189

129373-496

Operating Instructions

Table of Contents

11 Routine Maintenance ................................................................. 11-1

11.1 Preventive Maintenance Schedule ................................................ 11-1

11.1.1 Clean Chamber Drain Strainer ............................................... 11-3

11.1.2 Clean Chamber ...................................................................... 11-3

11.2 Weekly Maintenance ..................................................................... 11-4

11.2.1 Flush Chamber Drain ............................................................. 11-4

11.2.2 Change Printer Paper Roll ...................................................... 11-5

11.2.3 Change Printer Ink Cartridge ................................................. 11-7

11.3 Quarterly Maintenance .................................................................. 11-9

11.3.1 Replace Door Seal ................................................................. 11-9

12 Troubleshooting ......................................................................... 12-1

12.1 General .......................................................................................... 12-1

12.1.1 Typical Alarm Screen ............................................................. 12-1

12.1.2 Typical Alarm Printout ............................................................. 12-2

12.2 In-Cycle Alarms ............................................................................. 12-2

12.2.1 Too Long In Charge ................................................................ 12-2

12.2.2 Too Long In Exhaust ............................................................... 12-3

12.2.3 Too Long In Evacuation .......................................................... 12-3

12.2.4 Too Long In Air Break ............................................................. 12-4

12.2.5 Under Sterilize Temperature ................................................... 12-5

12.2.6 Over Sterilize Temperature ..................................................... 12-6

12.2.7 Door Unsealed ....................................................................... 12-7

12.2.8 Chamber Pressure/Temperature Failure ................................ 12-7

12.2.9 Exhaust Rate Too Fast ............................................................ 12-8

12.2.10 Exhaust Rate Too Slow ......................................................... 12-9

12.2.11 Reference Deviation Alarm................................................... 12-9

12.2.12 Door Pressure Lock (Hinged Door Models Only) ............. 12-10

12.3 Out-of-cycle Alarms .................................................................... 12-11

12.3.1 Too Long To Close Door ....................................................... 12-11

12.3.2 Too Long To Open Door ....................................................... 12-12

12.3.3 Pressure In Chamber ........................................................... 12-12

12.3.4 Waste Temperature Probe Failure ........................................ 12-13

12.3.5 Display Error ........................................................................ 12-14

12.3.6 Atmospheric Pressure Alarm ............................................... 12-14

Table of Contents (continued)

able of Contents (continued)

Section

Description

Page

Summary of Contents for Century






























































































































































































Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands

Amsco Century, Operator'S Manual

Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands