manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 62

6-27

Sterilizer Operation

Operating Instructions

129373-496

4. To begin Dart Warm-up, press 

DART WARMUP

.

3. Press 

TEST CYCLES 

button.

1.

PREVAC

4.

PREVAC

2.

GRAVITY

5.

GRAVITY

3.

LIQUID

6.

LIQUID

2

CYCLE SELECT

Pressing MAIN MENU returns display to
screen #1.

MAIN

MENU

TEST

CYCLES

3

CYCLE SELECT

LEAK

TEST

DART

DART

TEST

WARMUP

Pressing STANDARD CYCLES returns
display to screen #2.

Pressing MAIN MENU returns display to
screen #1.

MAIN

MENU

STANDARD

CYCLES

NOTE: If 

DART WARM-UP 

is pressed while the chamber door is open, a

display screen will appear directing the operator to close door before
continuing cycle operation. Operator must reselect DART WARM-UP after
the door is closed.

NOTE: If a cycle is started when the sterilizer has not been fully calibrated,
a display screen will appear indicating that the control is not calibrated.
Sterilizer must be calibrated by a qualified service technician before process-
ing loads.

5. Sterilizer automatically progresses through the following cycle phase:

NOTE: If an alarm occurs during cycle operation, refer to 

S

ECTION

 11, R

OUTINE

M

AINTENANCE

, for instructions on correcting the alarm condition.

NOTE: If power is lost during cycle operation, cycle either continues in same
phase or aborts if seal pressure is below 5 psig (0.34 Pbar) once power is
restored.

• Jacket Charge

– Jacket charges with steam to 131°C (268°F).

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands