Amsco Century Operator'S Manual Download Page 78

Page: 78 / 189

8-6

129373-496

Operating Instructions

Programming Cycle Values

•

Pressing

PURGE TIME

advances display to screen #28. Enter purge

time using the numeric keypad. Time appears on display as it is being
entered.

Pressing

←

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
cycle value and returns display to screen
#20.

CHANGE VALUES - PURGE TIME

RETURN

←

→

SET PURGE TIME

01:00

(Minutes:Seconds)

The purge time is

the amount of time spent in

the purge phase.

•

Pressing

PULSES

advances display to screen #29. Enter number of

pulses using the numeric keypad. Number appears on display as it is
being entered.

CHANGE VALUES - PULSES

RETURN

←

→

SET NUMBER OF PULSES

The number of pulses

is the total number

of vacuum pulses

in the cycle.

Pressing

←

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
cycle value and returns display to screen
#20.

Definition of

Cycle Value

Summary of Contents for Century






























































































































































































Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands

Amsco Century, Operator'S Manual

Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands