Amsco Century Operator'S Manual Download Page 134

Page: 134 / 189

10-23

Out of Cycle Options

Operating Instructions

129373-496

Pressing

←

→

on numeric keypad

moves the entry location to the left or
right, respectively.

Pressing CANCEL returns display to
screen #48 without changing the current
access code.

7.Enter the

new access code

using the numeric keypad. New access

code appears on display as it is being entered. Once the new code is
correctly entered, press

ENTER

CHANGE VALUES ACCESS CODE

←

→

CANCEL

ENTER THE NEW

ACCESS CODE.

ENTER

8.Screen #111 allows supervisor to designate which values can not be

changed by the operator. To lock out a specific value, press the
corresponding

values button

For example: Press

SETUP

to prevent the operator from changing the

setup values. Once pressed, the values button reads LOCKOUT.

NOTE: Pressing CYCLES advances display to screen #112. Screen
#112 allows supervisor to designate specific cycles which cannot be
changed by the operator.

Once all desired values are locked out, press

RETURN

111

LOCKOUT VALUES

TOO LONG

IN PHASE

TIME/

DATE

CYCLES

SETUP

RETURN

Summary of Contents for Century






























































































































































































Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands

Amsco Century, Operator'S Manual

Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands