manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 10

1-2

129373-496

Operating Instructions

Listing of Warnings and Cautions

Proper testing of the safety valve requires the valve to be operated under pressure.

  Exhaust from the safety

valve is hot and can cause burns.  Proper safety attire (gloves, eye protection, insulated overall) as  designated by
OSHA is required.  Testing is to be performed by qualified service personnel only.

WARNING – EXPLOSION HAZARD:

This sterilizer

 is not designed to process flammable compounds.

WARNING – SLIPPING HAZARD:

To prevent falls, keep floors dry 

by

 

immediately wiping up any spilled liquids or condensation in sterilizer loading

or unloading area.

WARNING – PERSONAL INJURY AND/OR EQUIPMENT DAMAGE HAZARD:

Regularly scheduled preventive maintenance is required

 for safe and reliable operation of this equipment.

Contact your STERIS Service Representative to schedule preventive maintenance.

When closing the chamber door, 

keep hands and arms out of the door opening and make sure opening is clear

of obstructions.

Repairs and adjustments to this equipment

 must be made only by fully qualified service personnel.  Maintenance

performed by inexperienced, unqualified persons or installation of unauthorized parts could cause personal injury
or result in costly equipment damage.

WARNING – STERILITY ASSURANCE HAZARD:

Load sterility may be compromised if the biological indicator or air leak test indicates a potential problem

.

If these indicators show a potential problem, refer the situation to a qualified service technician before using the
sterilizer further.

According to AAMI standards, a measured leak rate greater than 1 mm Hg/minute (1.3  mbar/min) indicates
a problem with the sterilizer.

 Refer the situation to a qualified service technician before using the sterilizer further.

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands