manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 86

8-14

129373-496

Operating Instructions

Programming Cycle Values

#3 = Door B is designated as the operating end (OE). Sterilizer must be

loaded from door B, and can be unloaded from door A or door B.
At end of cycle, operator must manually unseal the unload door by
pressing 

UNSEAL DOOR

 touch screen button (screen #65)

located on the same end as the door.

NOTE: Once the operating end (OE) door is opened, the non-
operating end (NOE) door cannot be opened until a complete
cycle is run. If the NOE door is opened, the OE door cannot be
opened until the NOE door is closed and sealed.

#4 = Door B is designated as the operating end (OE). Sterilizer must be

loaded from door B and unloaded from door A.  At end of cycle,
door A is automatically unsealed.

NOTE: Once the operating end (OE) door is opened, the non-
operating end (NOE) door cannot be opened until a complete
cycle is run. If the NOE door is opened, the OE door cannot be
opened until the NOE door is closed and sealed.

#5 = Door A is designated as the operating end (OE) door. Sterilizer

must be loaded and unloaded from door A; door B is locked out.
At end of cycle, door A is automatically unsealed.

#6 = Door B is designated as the operating end (OE) door. Sterilizer

must be loaded and unloaded from door B; door A is locked out.
At end of cycle, door B is automatically unsealed.

7. After all cycle value changes have been made, press 

CYCLE MENU

 button

on screen #22. Display returns to screen #15.

B (OE)

A (NOE)

➤

➤

➤

➤

➤

➤ ➤ ➤ ➤ ➤

load

unload

B (OE)

A (NOE)

➤

➤

➤

➤

➤

➤

➤

➤

➤

➤

load

unload

B (OE)

A (NOE)

➤

➤

➤

➤

➤

➤

➤

➤

➤

➤

load

unload

load

unload

B (OE)

➤

➤

➤

➤

➤

➤ ➤ ➤ ➤ ➤

A

locked

out

➤ ➤ ➤ ➤ ➤

➤

➤

➤

➤

➤

load

unload

A (OE)

B

locked

out

Pressing PREVIOUS returns display to
screen #21.

Pressing MAIN MENU returns display to
screen #1.

22

CHANGE VALUES - 1. PREVAC (PREVAC)

PRINT INT = 2 min

   VACUUM DRY = 10.0 inHg

DRY TIME = 5:00

INTERLOCK = 2

PREVIOUS

MAIN

MENU

CYCLE

MENU

Double Door

Units Only

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands