manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 65

6-30

129373-496

Operating Instructions

Sterilizer Operation

7. To begin Dart Test, press 

DART TEST

.

Pressing STANDARD CYCLES returns
display to screen #2.

Pressing MAIN MENU returns display to
screen #1.

3

CYCLE SELECT

LEAK

TEST

DART

DART

TEST

WARMUP

MAIN

MENU

STANDARD

CYCLES

NOTE:  If 

DART TEST

 is pressed while the chamber door is open, a display

screen will appear directing the operator to close door before continuing cycle
operation. Operator must reselect 

DART TEST

 after the door is closed.

NOTE: If a cycle is started when the sterilizer has not been fully calibrated,
a display screen will appear indicating that the control is not calibrated.
Sterilizer must be calibrated by a qualified service technician before
processing loads.

8. Sterilizer automatically progresses through the following cycle phases.

NOTE: If an alarm occurs during cycle operation, refer to 

S

ECTION

 12,

T

ROUBLESHOOTING

, for instructions on correcting the alarm condition.

NOTE: If power is lost during cycle operation, cycle either continues in the
same phase or aborts if seal pressure is below 5 psig (0.34 Pbar) once power
is restored.

• Jacket Charge

– Jacket charges with steam to 131°C (268°F).

• Activate Seal

– Door seal fills with steam and expands against the

sterilizer door opening, forming an air-tight seal.

• Purge

–

–

–

–

– Steam flows through the chamber for 1 minute.

NOTE: The projected cycle completion time shown on the display is
estimated. The control automatically evaluates the cycle progress and
corrects the estimated time at the beginning of each phase.

NOTE:  Current time, chamber pressure and chamber temperature are printed
at each transition point.

• Vacuum Pulse #1 Exhaust

– Chamber is exhausted to 4 psig (0.28 Pbar).

• Vacuum Pulse #1 Evacuate

– A vacuum is drawn in the chamber to

10  inHg (0.34 Vbar).

• Charge Pulse #1

– Chamber charges with steam up to 26 psig (1.8 Pbar).

• Vacuum Pulse #2 Exhaust

– Chamber is exhausted to 4 psig (0.28 Pbar).

• Vacuum Pulse #2 Evacuate

– A vacuum is drawn in the chamber to

10  inHg (0.34 Vbar).

• Charge Pulse #2

– Chamber charges with steam up to 26 psig (1.8 Pbar).

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands