manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 126

10-15

Out of Cycle Options

Operating Instructions

129373-496

Display Sensors is used to view the current temperature and pressure readings
of the sterilizer.

1. Press 

DISPLAY SENSORS

 on screen #87.

10.9  Display Sensors

Pressing PREVIOUS returns display to
screen #13.

Pressing MAIN MENU returns display to
screen #1.

2. Screen #92 lists the readings recorded by the sterilizer pressure and

temperature sensors at the time the 

DISPLAY SENSORS

 button was

pressed.

After viewing, press 

RETURN

. Display returns to screen #87.

92

TEMPERATURE AND PRESSURE DISPLAY

CHAMBER PRESSURE

=

00.0 psig

CHAMBER TEMPERATURE =

32.0 C

JACKET  TEMPERATURE

=

115.0 C

WASTE   TEMPERATURE

=

80.0 C

REFER   TEMPERATURE

=

32.0 C

MAIN

MENU

RETURN

Pressing MAIN MENU returns display to
screen #1.

87

OUT OF CYCLE OPTIONS

PREVIOUS

MAIN

MENU

SUPER-

VISORY

DISPLAY

SERVICE

SENSORS

MODE

STANDBY

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands