manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 92

9-4

129373-496

Operating Instructions

Programming Operating Parameters

Sterilizer uses the "too long in phase" values to monitor and control the length
of the associated cycle phases. Each "too long in phase" value is factory
programmed at 30 minutes.

To adjust the "too long in phase" values:

1. Access Change Values menu (screen #14) as described at the beginning

of this section.

2. Press 

TOO LONG IN PHASE

.

9.3  Too Long In

Phase

14

CHANGE VALUES

RETURN

MAIN

MENU

TOO LONG

IN PHASE

TIME/

DATE

Pressing RETURN returns display to
screen #13.

Pressing MAIN MENU returns display to
screen #1.

3. Screen #40 is the first of two menu screens which list the phase and its

currently set value. To change any of the listed values (parameters), press
the corresponding button.

NOTE: A definition of each value (parameter) is given on the corresponding
display screen.

Pressing RETURN saves all changed
parameters and returns display to screen
#14.

Pressing NEXT advances display to
screen #53.

Pressing MAIN MENU returns display to
screen #1.

40

CHANGE TOO LONG IN PHASE PARAMETERS

   TOO LONG IN:

CHARGE = 30:00

STERILIZE = 30:00

EXHAUST = 30:00

EVACUATE = 30:00

NEXT

RETURN

MAIN

MENU

CYCLES

SETUP

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands