manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 67

6-32

129373-496

Operating Instructions

Sterilizer Operation

11

CYCLE ABORT ACKNOWLEDGE

ARE YOU SURE

YOU WISH TO ABORT CYCLE?

If the cycle is aborted, the
cycle will end.  The cycle will safely exhaust or
air break to atmospheric pressure.  A vapor
removal phase will eliminate steam vapors in the
chamber.

CONTINUE

CYCLE

Pressing CONTINUE CYCLE resumes
cycle operation at the point where it was
interrupted. Display returns to the
corresponding in-cycle status screen.

ABORT

10

GRAVITY CYCLE

STATUS

PRINT

PHASE:

FAST EXHAUST

FAST EXHAUST TO:

2.0 psig

CHAMBER:

133.5 C

31.0 psig

CYCLE ABORTED.

10

GRAVITY CYCLE

STATUS

PRINT

PHASE:

AIR BREAK

TIME LEFT IN PHASE

1:00

CHAMBER:

90.5 C

5.0 inHg

CYCLE ABORTED.

Pressing STATUS PRINT generates a
printout of the current sterilizer chamber
status.

Pressing STATUS PRINT generates a
printout of the current sterilizer chamber
status.

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands