Amsco Century Operator'S Manual Download Page 85 | Manualshive

Page: 85 / 189

Amsco Century Operator'S Manual Download Page 85

8-13

Programming Cycle Values

Operating Instructions

129373-496

•

If sterilizer is equipped with double doors, pressing

INTERLOCK

ad-

vances display to screen #8. Enter interlock type using the numeric
keypad. Interlock type appears on the display as it is being entered.

NOTE: Default interlock type is #2. If different setting is desired, a
separate interlock type must be set for each cycle.

8

CHANGE VALUES - INTERLOCK TYPE

RETURN

1

2

3

4

5

6

<-

0

->

Pressing

←

or

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
cycle value and returns display to screen
#22.

SET INTERLOCK TYPE

2

The interlock type

determines which door

is used to load and unload the

sterilizer.

See operating manual for

description of types.

The following descriptions and illustrations explain each interlock type,
#0 through #6. Each door on the illustrations is labeled, "A" or "B", for
reference. Door A is located on the same end as the main power
disconnect switch (see Figure 3-2 for switch location). Door B is located
on the opposite end.

#0 = No interlocks. Either door can be used to load and unload the

sterilizer. Both doors can be open at the same time. At end of
cycle, both doors are automatically unsealed.

#1 = Door A is designated as the operating end (OE). Sterilizer must be

loaded from door A, and can be unloaded from door A or door B.
At end of cycle, operator must manually unseal the unload door by
pressing the

UNSEAL DOOR

touch screen button (screen #65)

located on the same end as the door.

NOTE: Once the operating end (OE) door is opened, the non-
operating end (NOE) door cannot be opened until a complete
cycle is run. If the NOE door is opened, the OE door cannot be
opened until the NOE door is closed and sealed.

#2 = Door A is designated as the operating end (OE). Sterilizer must be

loaded from door A and unloaded from door B. At end of cycle,
door B is automatically unsealed.

NOTE: Once the operating end (OE) door is opened, the non-
operating end (NOE) door cannot be opened until a complete
cycle is run. If the NOE door is opened, the OE door cannot be
opened until the NOE door is closed and sealed.

B (NOE)

A (OE)

➤ ➤ ➤ ➤ ➤

➤ ➤ ➤ ➤ ➤

load

unload

➤ ➤ ➤ ➤ ➤

➤

➤

➤

➤

➤

load

unload

B (NOE)

A (OE)

B (NOE)

A (OE)

➤ ➤ ➤ ➤ ➤

➤ ➤ ➤ ➤ ➤

load

unload

«
...
83
84
85
86
87
...
»

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands