manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 56

6-21

Sterilizer Operation

Operating Instructions

129373-496

• Charge

– Chamber charges with steam to the programmed sterilize

temperature.

• Sterilize

– Sterilize phase begins when chamber temperature is equal to

or greater than the programmed sterilize temperature. Chamber tempera-
ture is printed every 2 minutes (or printed after each programmed print
interval). The steam-to-jacket valve is regulated to maintain the chamber
at the sterilize control temperature (control temperature = sterilize tem-
pe overdrive temperature).

9

LIQUID CYCLE

PHASE:

CHARGE

CHARGING TO:

121.0 C

CHAMBER:

110.0 C

10.0

psig

PROJECTED CYCLE COMPLETION TIME:

58:40

m:s

STATUS

PRINT

ABORT

Pressing ABORT advances display to
screen #11. Refer to "Aborting Cycles,"
later in this section.

Pressing STATUS PRINT generates a
printout of the current sterilizer chamber
status.

9

LIQUID CYCLE

PHASE:

STERILIZE

TIME LEFT IN PHASE:

30:00

CHAMBER:

121.0 C

19.0

psig

PROJECTED CYCLE COMPLETION TIME:

50:40

m:s

STATUS

PRINT

ABORT

• Slow Exhaust

– Chamber is slowly exhausted until chamber pressure

reaches 0 psig (0 bar).

Pressing ABORT advances display to
screen #11. Refer to "Aborting Cycles,"
later in this section.

Pressing STATUS PRINT generates a
printout of the current sterilizer chamber
status.

9

LIQUID CYCLE

PHASE:

SLOW EXHAUST

EXHAUSTING TO:

0.0 psig

CHAMBER:

122.5 C

19.0

psig

PROJECTED CYCLE COMPLETION TIME:

20:40

m:s

STATUS

PRINT

ABORT

Pressing ABORT advances display to
screen #11. Refer to "Aborting Cycles,"
later in this section.

Pressing STATUS PRINT generates a
printout of the current sterilizer chamber
status.

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands