Amsco Century Operator'S Manual Download Page 93

Page: 93 / 189

9-5

Programming Operating Parameters

Operating Instructions

129373-496

Pressing

←

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
parameter and returns display to screen
#40.

•

Pressing

CHARGE

advances display to screen #41. Enter charge phase

value using the numeric keypad. Value appears on display as it is being
entered.

CHANGE VALUES - TOO LONG IN CHARGE

RETURN

←

→

SET TOO LONG IN CHARGE

30:00

(Minutes:Seconds)

The too long in

charge is the

allowable amount of

time that the chamber

has to reach the set

point during charge

pulse or charge phase

before an alarm occurs.

•

Pressing

STERILIZE

advances display to screen #52. Enter sterilize

phase value using the numeric keypad. Value appears on display as it is
being entered.

•

Pressing

EXHAUST

advances display to screen #42. Enter exhaust

phase value using the numeric keypad. Value appears on display as it is
being entered.

Pressing

←

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
parameter and returns display to screen
#40.

CHANGE VALUES - TOO LONG IN EXHAUST

RETURN

←

→

SET TOO LONG IN EXHAUST

30:00

(Minutes:Seconds)

The too long in

exhaust is the

allowable amount of

time that the chamber

has to reach 4 psig

before an alarm occurs.

CHANGE VALUES - TOO LONG IN STERILIZE

RETURN

←

→

SET TOO LONG IN
STERILIZE

30:00

(Minutes:Seconds)

The too long in

sterilize is the

allowable amount of

time that the sterilize

phase may go beyond the set

sterilize time. The

cycle will then abort.

Pressing

←

→

on numeric keypad

moves the cursor to the left or right,
respectively.

Pressing RETURN saves the changed
parameter and returns display to screen
#40.

Definition of

Parameter

Summary of Contents for Century






























































































































































































Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands

Amsco Century, Operator'S Manual

Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands