Amsco Century Operator'S Manual Download Page 137

Page: 137 / 189

10-26

129373-496

Operating Instructions

Out of Cycle Options

5. Enter operator's name, maximum of nine characters, using the alpha-

numeric keypad. Operator name appears at bottom of display as it is
being entered. Once name is correctly entered, press

RETURN

NOTE: Operator name appears inside the corresponding touch screen
button on screen #126 and at the beginning of each in-cycle printout.

STERILIZER - OPERATOR NAME

←

→

RETURN

OPERATOR NAME

---------

Pressing

←

→

moves the cursor to

the left or right, respectively.

6.Enter the

old access code

(access code currently programmed for the

selected operator) using the numeric keypad. Access code appears on
display as it is being entered. Once the old code is correctly entered,
press

ENTER

NOTE: Default access code is 0000.

STERILIZER OPERATION ACCESS CODE

←

→

CANCEL

ENTER THE OLD

ACCESS CODE.

ENTER

Pressing

←

→

on numeric keypad

moves the entry location to the left or
right, respectively.

Pressing CANCEL returns display to
screen #48.

SPACE

Summary of Contents for Century






























































































































































































Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands

Amsco Century, Operator'S Manual

Search results

Summary of Contents for Century

Reviews:

Brands by name

Popular brands