manualshive.com logo in svg

Amsco Century, Operator'S Manual

Share
Download
Amsco Century Operator'S Manual Download Page 161

12-6

129373-496

Operator Manual

Troubleshooting

Occurs if chamber
temperature exceeds
the maximum sterilize
temperature (Control
temp. + over temp.
value).

Screen with Service Instructions

12.2.6 Over Sterilize

Temperature

STATUS..

SERVICE INFORMATION:

236

OVER STERILIZE TEMPERATURE

→

→

→

→

→

STERILIZE TEMPERATURE IS ABOVE
SETPOINT BY MORE THAN PRESCRIBED
AMOUNT

CAUSES AND CORRECTION:
1.

STEAM PRESSURE MORE THAN 50 psig

→

→

→

→

→

CHECK STEAM SUPPLY PIPING

2.

CHAMBER STEAM TRAP MALFUNCTION

→

→

→

→

→

REPAIR

3.

SOLENOID VALVE MALFUNCTION

→

→

→

→

→

REPAIR S09

→

→

→

→

→

REPAIR S02

4.

CONTROL OUT OF CALIBRATION

→

→

→

→

→

RECALIBRATE (CONTACT QUALIFIED
SERVICE PERSON)

SERVICE

STATUS

PAPER

EXIT

MODE

PRINT

FEED

Alarm

Description

Screen with Operator Instructions

NOTE: The control temperature is
the value the sterilizer maintains
during the sterilize phase. This
value is 2°C above the cycle steril-
ize temperature set point. The over
temperature value is added to the
control temperature value to arrive
at the temperature which causes
this cycle alarm.

SILENCE

SERVICE

ALARM

HELP

CHAMBER:

000.0 C

0.0 psig

STERILIZER WILL:

•

AUTOMATICALLY TRY TO COMPLETE CYCLE

OPERATOR INSTRUCTIONS:
1. SILENCE ALARM
2. IF ALARM RECURS, ABORT CYCLE

AND CALL SERVICE

STATUS..

ALARM!

235

OVER STERILIZE TEMPERATURE

ABORT

Summary of Contents for Century






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands