Zoomlion ZCC1100 Скачать руководство пользователя страница 69

Страница: 69 / 291

Operator’s Manual for Crawler Crane

rip
tio

Cra

Operator’s Manual for Crawler Crane

ZCC1100H Crawler Crane

2-47

(3) Do not lift a load in the area which is not in the lifting capacity range, otherwise the

crane may topple over or be damaged;

(4) The value in the chart is the lifting capacity when the crane is working with 61740

Lbs (28t) rear counterweight and 22050lbs (10t) central counterweight in 360° range.

(5) The value in the chart is the maximum lifting capacity of the crane, including the

weight of lifting device, hook, wire rope at the end of hook and so on.

(6) The crawler carriers of the crane are extended completely.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 69 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: