Zoomlion ZCC1100 Скачать руководство пользователя страница 190

Страница: 190 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-50

If derricking mechanism does not work for a long time, turn on derricking ratchet pawl

switch, and then reel off derricking winch slowly until ratchet pawl is engaged into the

ratchet wheel completely. At this time, the derricking rope can not be unwound

continuously.

When there is a need to move the boom, turn off derricking ratchet pawl switch, and

then spool up derricking winch to make ratchet pawl disengaged from the ratchet

wheel.

CAUTION

(1) Derricking operation should be performed stably. When the crane is lifting a load,

jerky operation will bring great impact on the crane.

(2) When the crane is lifting a load, the operator should not derrick boom towards

dangerous directions. Otherwise, the crane may topple over.

(3) Before derricking mechanism is operated, first derrick boom down a little, and then

operate ratchet wheel mechanism according to the correct methods mentioned

above. In this way, ratchet pawl can be disengaged from ratchet wheel successfully.

Do not operate the derricking mechanism before the ratchet pawl is disengaged

from ratchet wheel completely.

(4) Before switching off the derricking mechanism, press ratchet wheel switch and hold

it till the ratchet pawl engages with the ratchet wheel tooth.

(5) If ratchet pawl is not disengaged from ratchet wheel completely, derricking winch is

only permitted to spool up.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 190 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: