Zoomlion ZCC1100 Скачать руководство пользователя страница 147

Страница: 147 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-7

CAUTION

The horn can only be actuated in emergency condition to warn the person in the vicinity

of the crane.

4.1.4 Left control panel

Off

H3 Free Fall

Free Fall Chief

H2 Free Fall

H1 Free Fall

Off

Figure 4-5 Left control panel

When the crane has free-fall function, the left control panel will be described in the table 4-5.

Table 4-5

Description of left control panel (crane with free-fall function)

No.

Names of the

switches

Remarks

Free-fall master switch

Turn on this switch before any free-fall operation of hoisting

winch.

H1 free-fall switch

In order to carry out free-fall operation of H1 winch, the

operator must first turn on “free-fall master switch”, and then

switch on “H1 free-fall switch”.

H2 free-fall switch

Control the free-fall operation of H2 winch. The operating

method is the same as above.

H3 free-fall switch

Control the free-fall operation of H3 winch. The operating

method is the same as above.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 147 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: