Zoomlion ZCC1100 Скачать руководство пользователя страница 230

Страница: 230 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dismantli

5-24

When central counterweight is aligned with the undercarriage central section, attach the

hooks at the upper side of central counterweight to the attachment points on the

undercarriage central section. See the figure 5-25.

Figure 5-25 Attachment of upper hook of central counterweight

d) Slowly extend mounting cylinder to make central counterweight rotate around the upper

attachment points until the central counterweight is in contact with the undercarriage

central section completely.

e) After the central counterweight is assembled, keep the connection between the mounting

cylinder and central counterweight. See the figure 5-26.

Unwind derricking rope properly, and then retract mounting cylinder slowly. At this time,

main boom pivot section is pulled down to a proper position with the help of mounting

cylinder. See the figure 5-27.

g) When main boom pivot section can be lowered by itself, remove the rope between

mounting cylinder and central counterweight. Then the assembly of central counterweight

on one side of crane is finished.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 230 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: