Zoomlion ZCC1100 Скачать руководство пользователя страница 128

Страница: 128 / 291

履带起重机操作手册

安

全
准

则

Operator’s Manual for Crawler Crane

lin

3-46

ZCC1100H Crawler Crane

S/N

Instructions

Examples

It is prohibited to make any

modifications to the crane without

permission; otherwise you should take

the consequences.

Stop the crane operation if one of the conditions in the table 3-12 occurs:

Table 3-12 Conditions to stop and inspect the crane

S/N

Conditions to stop the crane

The crane is overloaded or the weight of load

is uncertain

The load falls down due to bad binding or

hanging

No protective mat is added between the

edges of load and wire rope

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 128 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: