Zoomlion ZCC1100 Скачать руководство пользователя страница 281

Страница: 281 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-75

Figure 5-67 Assembly of fixed jib

CAUTION

(1) Check whether the spring is mounted in the outer pipe of front tilting-back support

of fixed jib. If the spring is not mounted, the tilting-back support can not prevent it

against falling, then the fixed jib may topple over.

(2) Make sure that the hoisting rope near the boom head is not exposed to crushing

force during rope reeving and boom raising process.

(3) Ensure that the nylon guide on fixed jib head is always rolling on the ground before

fixed jib is lifted away from the ground.

(4) Take great care to connect rear titling-back support of fixed jib to main boom head.

(5) Install the pin spindle correctly on front tilting-back support according to the

procedure (f), otherwise, the fixed jib will be damaged.

Inner pipe

Outer pipe

Pin spindle

End of inner pipe

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 281 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: