Zoomlion ZCC1100 Скачать руководство пользователя страница 113

Страница: 113 / 291

履带起重机操作手册

安

全

准

则

Operator’s Manual for Crawler Crane

Sa
fe

lin

ZCC1100H Crawler Crane

3-31

CAUTION

To travel crawler crane uphill, the following conditions must be observed:

(1) The ground must be able to support possible ground pressure.

(2) The friction coefficient between roadway and track pad must be large enough to

produce enough drive forces.

(3) Slippery ground can cause the crane to slip sideways and move into an

impermissible side incline position. There is a danger of accidents.

(4) The slewing table must be aligned to the crawler carriers and must be secured to

prevent it from turning.

(5) The maximum permissible wind velocity is 9.8m/s.

(6) Side incline is not permitted!

(7) Travel slowly, and perform all acceleration and deceleration motions with utmost

caution.

(8) The transfer from the horizontal to the incline and from the incline to the horizontal

must be made very evenly. The change of gradient must be continuous.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 113 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: