Zoomlion ZCC1100 Скачать руководство пользователя страница 183

Страница: 183 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-43

Turn to left with a crawler

Turn to right with a crawler

Figure

4-39

Turning with a crawler

CAUTION

The high speed is not allowed when the crane is turning with a crawler.

1) Differential steering

Figure 4-40 Differential steering

Differential steering to right:

Depress left travel gear pedal forwards heavily, while depressing right travel gear pedal

forwards slightly to make the speed of left crawler faster than that of right crawler.

Differential steering to left:

Depress right travel gear pedal forwards heavily, while depressing left travel gear pedal

forwards slightly to make the speed of right crawler faster than that of left crawler.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 183 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: