Zoomlion ZCC1100 Скачать руководство пользователя страница 235

Страница: 235 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-29

5.2.5.4 Lifting of rear counterweight

a) Move basic machine until the axes of slewing table in longitudinal direction, traveling

direction and central line of counterweight are aligned with each other. See the figure 5-32.

Figure 5-32 Moving basic machine

b) Travel basic machine backwards until the counterweight lifting cylinder is positioned above

the mounting hole of counterweight base plate. Connect counterweight anchoring rods.

See the figure 5-33.

Figure 5-33 Connection of counterweight anchoring rods

Counterweight plates

Anchoring rods

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 235 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: