Zoomlion ZCC1100 Скачать руководство пользователя страница 188

Страница: 188 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-48

4.5.6.3

Derricking mechanism

a) Components of derricking mechanism

Through changing the length of wire rope reeved between derricking pulley blocks

(includes derricking crown block and derricking traveling block), the derricking mechanism,

via derricking winch, can adjust boom angle so as to change the working radius. We can

use A-frame and boom frame to carry out derricking movement. During derricking, the

derricking crown block is located at the top of A-frame, while the derricking traveling block

is on the other end of anchoring rod, so the boom angle can be changed with the variation

in the length of wire rope between the derricking pulley blocks.

Figure 4-43

Components of derricking mechanism

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 188 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: