Zoomlion ZCC1100 Скачать руководство пользователя страница 137

Страница: 137 / 291

履带起重机操作手册

安

全

准

则

Operator’s Manual for Crawler Crane

Sa
fe

lin

ZCC1100H Crawler Crane

3-55

Ser. No.

Signal

Raise boom

Lower boom

Raise boom slowly

Description

With arm stretched

sideways horizontally,

thumb pointing upwards,

the remaining fingers

closed, wave forearm up.

With arm stretched

sideways horizontally,

thumb pointing

downwards, the

remaining fingers closed,

wave forearm down.

Bend the left arm. Move

the thumb up and down,

pointing upwards. Place

the right arm above it.

Illustration

Ser. No.

Signal

Lower boom slowly

Stop

Emergency stop

Description

Bend the left arm. Move

the thumb up and down,

pointing downwards.

Place the right arm below

it.

Stretch out one arm

horizontally. The palm

faces downwards. Swing

the arm to one side of the

body.

Stretch out both arms

horizontally. The palms

face downwards. Swing

the arms to both sides of

the body.

Illustration

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 137 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: