Zoomlion ZCC1100 Скачать руководство пользователя страница 155

Страница: 155 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-15

4.2.2.2

Engine information

Speed 100

0 rpm

500

1000

1500

2000

2500

3000

0 hour

120

210

1/2

WaterTEMP

Oil Pressure

Fule Lever

0℃

0.0Bar

0.0%

Figure 4-12

Screen of engine information

The screen of engine information will be described in detail in the table 4-10.

Table 4-10

Description of engine information screen

No.

Engine information

Remarks

Engine speed and

working time

Show current engine speed and total working hours

Engine coolant

temperature

Show engine coolant temperature

Engine oil pressure

Show engine oil pressure

Fuel level

Show fuel level in the fuel tank

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 155 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: