Zoomlion ZCC1100 Скачать руководство пользователя страница 257

Страница: 257 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-51

Fixed jib can be assembled to required three lengths of 19'8" (6m), 39'4" (12m) and 59'1" (18m).

See the figure 5-47 and table 5-11.

Table 5-11 Assembly of fixed jib

Fixed jib length

Assembly sequence of

fixed jib sections

Fixed jib length

Assembly sequence of

fixed jib sections

19'8" (6m)

G31+G32

59'1" (18m)

G31+G33×2+G32

39'4" (12m)

G31+G33+G32

DANGER

Main boom sections and main boom anchoring rods in this boom configuration are

bolted together in the same way as those in “main boom” configuration (The main boom

length in “Main boom with fixed jib” configuration varies from 101'9" (31m) to 180'5"

(55m). For the detailed information, refer to Section 5.4.1.

G33

G32

G31

G33

G31

G32

G33

Figure 5-47 Assembly of fixed jib

5.4.2.2 Components of fixed jib anchoring rods

The anchoring rods under “main boom with fixed jib” configuration comprises main boom

anchoring rods, fixed jib front anchoring rods and fixed jib rear anchoring rods.

For the components of main boom anchoring rods, see Section 5.4.1.2 “Combination of main

boom anchoring rods”. (The main boom length in “Main boom with fixed jib” configuration varies

from 101'9" (31m) to 180'5" (55m).)

The combination of fixed jib anchoring rods is described as follows.

19'8" (6m)

39'4" (12m)

59'1" (18m)

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 257 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: