Zoomlion ZCC1100 Скачать руководство пользователя страница 287

Страница: 287 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-81

5.7 Assembly and dismantling of tip boom

Figure 5-71

Assembly of tip boom

The procedures for assembly of tip boom are shown in figure 5-71:

–

Align the upper connecting hole of tip boom with the A hole in main boom head.

–

Insert pin spindle (part 2) and secure it with cotter pin (part 1).

–

Align the lower connecting hole with the B hole in main boom head.

–

Insert pin spindle (part 3) and secure it with cotter pin (part 1).

The procedure for dismantling tip boom is the opposite of assembly.

CAUTION

Slowly raise and lower main boom with tip boom to prevent tip boom against damage

due to the impact brought by jerky operation.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 287 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: