Zoomlion ZCC1100 Скачать руководство пользователя страница 239

Страница: 239 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-33

Figure 5-35 Fixation of piston rod of mounting cylinder

5.2.6.2 Fixation of mounting cylinder

Procedure for fixing mounting cylinder:

–

Retract mounting cylinder, and then align the attachment point of mounting cylinder with

the pin hole at position B on the pivot section.

–

Lower main boom pivot section to a proper position so that the operator can fix the cylinder

at position B on the pivot section underneath the boom.

–

Remove the fixable strap.

–

Retract the mounting cylinder completely. See figure 5-36.

Figure 5-36 Fixation of mounting cylinder

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 239 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: