Zoomlion ZCC1100 Скачать руководство пользователя страница 146

Страница: 146 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-6

4.1.3.2 Right control lever

1 2 3

Figure 4-4

Illustration of right control lever operation

As shown in the figure 4-4, the left is the operating board for right control lever. It is stuck on the

left glass of the cab. The four directions shown on the right means that the control lever can be

moved forwards, backwards, leftwards and rightwards. There are two buttons on the control

lever. For their functions, please see the table 4-4.

Table 4-4

Operation of right control lever

No.

Meaning of the

symbol

Remarks

Horn

Correspond to the left button on the top of control lever. It is

used to control the horn.

Reel off H1

Push right control lever forwards, reel off H1.

High speed

Correspond to the right button on the top of control lever. It is

used to control the high-speed operation of H1 winch, H3

winch and right travel gear.

Reel off H3

Move right control lever to right, reel off H3.

Reel off derricking

winch

Move right control lever to right, reel off derricking winch.

Spool up H1

Pull right control lever backwards, spool up H1.

Spool up H3

Move right control lever to left, spool up H3.

Spool up derricking

winch

Move right control lever to left, spool up derricking winch.

Right

Front

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 146 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: