Zoomlion ZCC1100 Скачать руководство пользователя страница 220

Страница: 220 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dismantli

5-14

5.2.2.4 Assembly of right crawler carrier

The process of assembling right crawler carrier:

a) Confirm that left crawler carrier is in contact with the ground (see the figure 5-14). At this

time, the crane is inclined slightly, and the superstructure can slew freely.

b) Lift right crawler carrier from the low-loader, and assemble it onto the undercarriage

central section by use of mounting cylinder and main boom pivot section. If necessary, use

right horizontal cylinder to assemble crawler carrier.

Adjust the height of support cylinder to allow left and right crawler carriers to contact the

ground. Extend right horizontal cylinder to working position.

Figure 5-14 Assembly of right crawler carrier

DANGER

When only one crawler carrier is attached on the crane, the operator must first make this

crawler carrier come into contact with the ground, and then slew the tail end of slewing

table above the crawler carrier. Otherwise, serious injury or property damage will occur.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 220 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: