Zoomlion ZCC1100 Скачать руководство пользователя страница 214

Страница: 214 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dismantli

5-8

2600

Figure 5-5 Raising basic machine via support cylinders

2637

8'8"

1040

Figure 5-6 Supporting basic machine via support cylinders

CAUTION

If support cylinders are not lifted high enough, the operator can put the solid squared

timbers underneath the support plates.

Undercarriage control levers, which are located in the front of undercarriage central section,

can control four support cylinders and two horizontal cylinders. For detailed operation, please

see the operating board on the protective cover of control lever.

Insert the plug of auxiliary remote control box into the socket of junction box on the rear right

side of slewing table to establish electrical connection of auxiliary remote control box (see the

figure 4-48).

Unit: ft (mm)

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 214 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: