Zoomlion ZCC1100 Скачать руководство пользователя страница 221

Страница: 221 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-15

5.2.2.5 Follow-up operation

After left and right crawler carriers are attached on the crane, dismantle folding brackets so that

the horizontal anchoring rods can be connected, and central counterweight can be assembled.

See the figure 5-15.

Figure 5-15 Dismantling of folding brackets

a) Retract support cylinders, put support plates on the attachment points at the side of folding

brackets, disconnect hydraulic connection of folding brackets and tilt support cylinder. See

the figure 5-16.

Figure 5-16 Folding brackets to be dismantled

b) Dismantle folding brackets by use of mounting cylinder or other device, and then connect

the horizontal anchoring rods.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 221 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: