Zoomlion ZCC1100 Скачать руководство пользователя страница 243

Страница: 243 / 291

Operator’s Manual for Crawler Crane

Assembly

and

Dism

antling

5-37

5.4 Boom configuration

5.4.1 Main boom (S-1)

5.4.1.1 Components of main boom (S-1)

Main boom, whose length varies from 42'8" (13m) to 219'10" (67m), consists of basic boom and

main boom intermediate sections. The basic boom is 42'8" (13m) long, including main boom

pivot section (G11) (21'4") and main boom head (G12) (21'4"). There are three types of main

boom intermediate section: 3m main boom intermediate section (G13) (9'10"), 6m main boom

intermediate section (G14) (19'8") and 9m main boom intermediate section (G15) (29'6").

The longest main boom of 219'10" (67m), overview:

Code

Names of components

Qty.

G11

Main boom pivot section

(21'4")

G12

Main boom head (21'4")

G13

3m main boom intermediate

section (9'10")

G14

6m main boom intermediate

section (19'8")

G15

9m main boom intermediate

section (29'6")

G15A

9m main boom intermediate

section A (29'6")

Figure 5-38 Combination of 219'10" (67m) main boom

G14

G11

G13

G15

G15A

G12

G15

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 243 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: