Zoomlion ZCC1100 Скачать руководство пользователя страница 151

Страница: 151 / 291

Operator’s Manual for Crawler Crane

Crane

Operation

4-11

No.

Names of switches

Functions

Mounting cylinder

switch

Turn on this switch to operate mounting cylinder on main

boom pivot section, and turn off H2 winch switch at the same

time.

Oil cooling fan switch

Turn on this switch to make the oil cooling fan work when

there is a need to cool the hydraulic oil.

Winch low-speed

switch

All winch movements will slow down after the switch is turned

on.

Travel gear switch

Turn on this switch to operate the travel gear.

CAUTION

(1) Never operate H2 winch and mounting cylinder at the same time.

(2) Never operate derricking winch and H3 winch at the same time.

For reference only.

Operators manual should be consulted and adhered to.

Содержание ZCC1100




































































































































































































































































































Результаты поиска

Содержание ZCC1100

Отзывы:

Zoomlion ZCC1100, Руководство оператора, Страница: 151 / 291

Результаты поиска

Содержание ZCC1100

Отзывы: