7-FRONT FORK COMPONENT
42
CHK
ADJ
FIG.7 FRONT FORK
COMPONENT
Instrument function description
Instrument function:
①
EFI failure signal light;
②
ABS anti-lock braking system signal;
③
MODE key;
④
0D0 long odometer;TRIP
short odometer;
⑤
total mileage;
⑥
SET key;
⑦
Engine rev instrument
；⑧
km mark;
⑨
ECO indicator light;
⑩
battery low voltage prompt symbol;
；
⑪
gear;,
⑫
fuel oil level meter.
⑴
When the right hand presses the " " button of the sub switch (as shown in the lower left figure), the ignition
route is turned on, and the meter is turned on:
The screen shows all the content, while the engine speed scans to the maximum scale and then falls back to
normal mode.
⑵
) Short press the " " button. If the EFI failure signal
①
is not activated, it is normal. If it is not bright, it
indicates that the EFI system is abnormal. If the engine is started, it may cause damage. If the start is successful,
the fault signal lights up during operation, and the fault reported by the electric spray indicates that the electronic
fuel injection system is abnormal. Please stop the vehicle in a safe location and contact the company's designated
after-sales shop to check the vehicle's electronic spray system
⑶
When the motorcycle is energized and the parking is stopped by short pressing the " " button, the ABS anti-
lock braking system signal light
②
will automatically light up. When the vehicle speed exceeds 5 km/h, it will
automatically extinguish. Otherwise, it is indicated that the ABS is faulty. The aftermarket shop inspects and
repairs the motorcycles.
⑷
When the oil change indicator light is on, turn off the engine after stopping the vehicle in a safe position, and
check that the oil amount is sufficient. If it is not enough, it needs to be added as soon as possible; if it has been
driven to a certain mileage, it needs to be replaced as soon as possible.
⑸
ODO long odometer
④
TRIP short odometer
⑤
Long-short-range switching: In the TRIP mode, press the MODE button shortly to switch to "ODO". In the 0D0
mode, press the MODE button shortly to switch to the "TRIP" mode. Press and hold the SET button for a short
distance to clear. ODO Long mileage total mileage can not be cleared; TRIP can record single or multiple
accumulated mileage can be cleared.
⑹
In the "ODO" mode, press and hold SET
⑥
to enter the time mode. The MODE key is incremented by the
hour; the SET key long press to enter the minute setting flashes at the same time, the MODE competition
increases by short minutes, and long press the SET key to complete the time setting. If the battery is removed or
the loss of electricity clock is displayed from "12:00".
⑺
The tachometer displays the speed of the engine, indicating the number of revolutions of the engine crankshaft
per minute. 10000-12000rpm is the red warning zone of engine speed (red printing section).
⑻
Long press MODE key
③
in "0D0" mode to switch the speed between mph and km/h, and the odometer
switches between mile and km
Press the "ECO" button ECO indicator
⑨
shows "E" to indicate that it is in the normal economy mode; the
button pops up to show "S" to indicate that it is in power mode.
⑼
When the battery low voltage indication symbol
⑩
is flashing, it indicates that the battery voltage is lower
than 11.5
±
0.25V. Please contact our designated after-sales service store to check, charge or replace the battery
as soon as possible.
⑽
Fuel level table
⑫
shows that the 8th stage indicates that the fuel tank is full. When the fuel level drops to
approximately 1L, the fuel indicator flashes and fuel should be replenished as soon as possible.
Содержание ZT250-R
Страница 1: ...ZT250 R EURO IV 2021 03 01 Service manual...
