Zontes ZT250-R Скачать руководство пользователя страница 19

Страница: 19 / 76

4-REAR FORKLIFT COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251300-063093 Plywood M6×11×15(color zinc)

1244100-006000 ZT250

－

S rear liceness rubber buffer

1224200-091000 ZT310

－

R rear mudguard fender

1270300-273000

φ8 clip(L=73)

1174200-035000 ZT310 rear turn signal (including license plate light)

1174100-002000 ZT250

－

S rear reflector

1251100-102000 Non

－

standard bolt M6×16(304 stainless steel)

1274100-057095

Flanging bushing φ6.2×φ8.5×3.5

＋

φ14×1.5

1244100-052000

Buffer rubber of flanging bushing (φ8.5×φ14×1)

1250502-010093

GB96.1φ6(color zinc)

1274100-018000 ZT250

－

S anti

－

hot plate sleeve, muffler

1184100-114000 ZT250

－

R auxiliary fender extension cable

1244200-082000 ZT310 Rear sub fender wire rubber plug

【1】

FIG.3 REAR FORKLIFT

COMPONENT

Rear sub mudguard component 3

PROCEDURE:

●

Back reflector, license plate cushion rubber

Flip to the back, remove the nut

①

that comes with the rear reflector

⑹

, remove the clamp

⑷

and the back

reflector. Remove the plate cushion rubber

⑵

and remove the 2 plywood nuts

⑴

on the back of the rear mudguard

fender

⑶

●

Steering lights, fender sub-assemblies

Remove the bolts

⑺

on the left and right sides, and remove the flange bushing

⑻

, cushion rubber

⑼

, anti-

scalding bushing

⑾

and gasket

⑽

. Disassemble the turn signal and fender subassembly. Note that the sub-mud

switch cable

⑿

cannot be forcibly pulled.

●

fender sub-assembly

Remove the 2 plywood nuts

⑴

and retaining rubber plug

⒀

from the fender subassembly

⑶

●

turn signal subassembly

Remove the 2 plywood nuts

⑴

from the turn signal

⑸

. Remove the 3 joints of

②

and remove the sub-mud

switch cable

⑿

CAUTION:

●

Do not pull the cable hard when removing the sub-mud switch.

●

When reassembling, check if there is any pressure on the wire to prevent it from tightening.

Short circuit caused by bolts. Pay attention to the lamp connector, do not insert the wrong, turn left

Green + orange; right turn signal is green + blue; license plate light is green + pink.

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды