manualshive.com logo in svg

Zontes ZT250-R, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT250-R Скачать руководство пользователя страница 32

5-PEDAL COMPONENT

31

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1

1251100-123093 Non-standard bolts M8X25(environemntal color)

1

2

1274100-092000 ZT250

－

R left foot pedal

1

3

1251500-048000 ZT250

－

S Pedal support gasket

1

4

1251100-061093 Hexagonal flange bolts (environmental color zinc)

2

5

1274100-043000 Miniature rod end ball bearing SALJK6C

1

6

1274200-160000 ZT310

－

T shift lever step rocker

1

7

1250303-010093 GB6177.1M6

（

environmental color)

2

8

1274100-012000 ZT250

－

S Pedal pin

1

9

1274100-035000 ZT250

－

S Foot pedestal

1

10

1264100-006000 ZT250

－

S Pedal circlip

1

11

1264100-003000 ZT250

－

S front left foot pedal torsional spring

1

12

1274200-193000 ZT310

－

X front left pedal assembly (improved)

1

13

1250301-018093 GB6170M6

－

LH (environmental color zinc)

1

14

1274100-096000 ZT250

－

R shift lever adjustment screw

1

15

1250301-020093 GB6170M6 (environmental color)

1

SAJK6C

16

1274100-042000 Miniature rod end ball bearing SAJK6C

1

17

1274100-039000 ZT250

－

S shift lever spline rocker arm

1

18

1244200-024000 ZT310

－

X footrest gum cover

1

19

1274200-051000 ZT310

－

X footrest gum cover fixed plate

1

20

1250205-038000 GB70.2M5×12(stainless steel)

1

21

1032142-041000 ZT310

－

X front left pedal

1

SALJK6C

22

1274200-254093

Bush Φ12×Φ6×19 (environmental color)

1

23

1251100-224000 Non

－

standard ball stud M6 × 26

1

24

1250501-010000

GB93φ6 spring pad

1

GB6170M6

－

LH

(environmental color zinc)

PROCEDURE:

●

Front left foot pedal

  Remove the tool to remove the card spring 

⑽

, the foot pin shaft 

⑻

 will be removed, then the front left foot step

⑿

, foot twist spring 

⑾

●

Shift lever component

Remove the bolt 

⑴

 with a plum spanner and pull the foot support 

⑼

 in the direction outward. Remove the support

pad

⑶

 and the left foot bracket 

⑵

; Remove the shift lever assembly.

 Once with a ring spanner remove the nut 

⑺

, bolt (4), the shift lever treadle rocker rocker arm 

⑹

, shift lever key

rocker arm 

⒄

 removed.

Loosen the nut 

⒀

 

、⒂

 with the open spanner, remove the adjusting rod 

⒁

,and then separate the joint bearing

⑸

、⒃

.Finally,Remove the nut

⒀、⒂。

●

Foot pedal with rubber for after sales service

Hold the left front pedal

⑿，

 and remove the bolt (20)with tool

，

.Remove the spring pad(24)

、

rubber sleeve 

⒅

、

 fixing piece

⒆、

left pedal(21)

。

Remove the bolt(23)

，

then take off the bushing

（

22

）

.

CAUTION:

●

In the process of removing, you should fix the bike to prevent from the accident.

●

Pay attention to the hexagonal nuts at both ends of the joint bearing and adjusting rod (the right hand side of

the engine shift shaft, near the foot to the left) when reassembling.

●

Pay attention to the alignment of the support gasket and the support flange to assemble in place.

●

It can reduce the resistance of Shift lever rocker arm  by applying lubricating grease evenly on the surface of

foot support cylinder.

●

Since 20th Mar 2020,add a  spring washer(24) prevent the pedal rubber sleeve from loosening.

FIG.5 PEDAL

COMPONENT

Left pedal support component-2

Foot sales parts

Содержание ZT250-R













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды