Zontes ZT250-R Скачать руководство пользователя страница 13

Страница: 13 / 76

2-FRAME&ENGINE COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251300-057093 Non-standard nut M10×1.5

（

dacromet

）

1020241-225000 ZT250

－

R Upper hanging piece

out of stock

1020242-385000 ZT310

－

V Upper hanging piece

1251112-003093 M6×45 Hexagonal flange face 9.8 level bolt.

1274100-033000 ZT250

－

S Right support of down wind deflector

1251300-059093 125 Spindle nut of rear forklift M14×1.5

（

dacromet

）

1274100-009000 ZT250

－

S The axle sleeve of rear forklift

4024100-024000 ZT250 aluminum rear fork assembly(bearing/oil sealing

1252200-016093 250 Rear forklift axle 14×310

（

dacromet

）

1251100-086093 Non-standard bolts M10×1.5×112

（

dacromet

）

4044100-022051 ZT173YMM Output chain wheel cover

1274100-034000 ZT250

－

S Lower wind deflector left support

1251112-005093 M6×75 Hexagonal flange face 9.8 level bol

1251100-132003 Non-standard bolts M10×1.5×80

（

dacromet

）

4024100-031000 ZT250

－

R Bracket

PROCEDURE:

●

Chain wheel cover

Dismantle the left side bolt

⑶

of the engine with the sleeve and remove the chain wheel cover

⑽

●

Bracket engine hanging

Use the sleeve to cover the head of the bolt

⒀

then dismantle the nut

⑴

with the sleeve. Remove the

bolt then dismantle the bracket

⒁

Use the sleeve to cover the head of the bolt

⑼

, remove the nut

⑴

with the sleeve, then emove the bolts.

●

Hanging piece

Use the sleeve to cover the head of the bolt

⒀

and remove the nut

⑴

with the sleeve. Can not remove

the bolt

⒀

and the hanging piece

⑵

●

Engine middle part,frame and rear forklift component

Use the sleeve to cover the head of the bolt

⑻

and remove the nut

⑸

with the sleeve. Other parts

cannot be removed.

●

Engine

Both persons hold the left and right boxes of the engine. One person takes the bolt

⒀

and hanging

piece

⑵

off. Remove the rear flat fork ASSY

⑺

. Support the engine to shift to one side, and pay

attention to safety during the movement. Put the engine flat on the ground.

●

Wind deflector support, rear forklift sleeve

Remove the bolts

⑶

with the sleeve then remove the left support

⑾

and right support

⑷

of the wind

deflector.

ZT250

－

R Upper hanging piece ZT310

－

V Upper hanging piece

FIG.1FRAME&ENGINE

Frame&Engine

CAUTION:

●

It is necessary to remove the seat cushion, fuel tank, side cover, pedal support, wind deflector, shift lever,

muffler, radiator and pipe, cable, air filter joint, chain, engine negative pole, etc.

●

Use appropriate tools to support the motorcycle to prevent motorcycle dumping during disassembly. Single

operation is forbidden.

●

The waste oil needs to be collected and returned to qualified institutions. It is forbidden to dump and pollute

the environment and the source of water.

●

Please pay attention to safety to prevent accident.

●

It must be operated the engine with more than one people at the same time when removing the engine.

●

All standard parts must meet the standard torque value when reassembling, and refill the engine oil according

to the operation instruction.

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды