manualshive.com logo in svg

Zontes ZT250-R, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT250-R Скачать руководство пользователя страница 23

4-REAR FORKLIFT COMPONENT

22

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1

1251100-105000 Adjuster bolts M10X70 (304 stainless steel)

2

2

1251300-050000 Adjuster nut M10 (304 stainless steel)

2

3

1032142-073035 ZT310 Right Chain adjuster (titantium Gold )

1

4

1251300-067000 Right adjuster(Titanium) 

1

110N.m

5

1032142-072035 Left adjuster (Titanium)

1

6

1094100-032000 ZT250-R Rear wheel hollow shaft 

1

7

1274200-002000

Rear wheel right shaft sleeve φ20×φ28×φ38×18.5

1

8

1244200-050000 ZT310

－

T cushion gum

5

9

1094200-011000 ZT310

－

R sprocket

1

10

1080100-068000 ZT310 

－

 T, 520

－

42 T sprocket

1

11

1251300-057093 Non-standard bolts M10X1.5 

5

12

1274100-106000 ZT250

－

R rear wheel left sleeve φ20×φ30×φ35×12.9

1

FIG.7 REAR FORKLIFT

COMPONENT

Rear wheel component 1

PROCEDURE:

●

Rear wheel assembly

   Disassemble rear wheel axle nut 

⑷

with socket sleeve.

   Use open spanner to move chain adjuster nut 

⑵

 on both sides towards rear wheel axle until they reach chain adjusting

bolt 

⑴

. Then rotate the bolt and nut towards motorcycle front direction till the end.

  Push rear wheel assembly towards motorcycle front direction and take off the chain from sprocket.
  Hold the rear wheel assembly. Punch rear wheel axle 

⑹

 with rubber hammer. Take off right chain adjuster 

⑶

,right axle

sleeve 

⑺

, rear tire and rim assembly, left axle sleeve 

⑿

, left chain adjuster 

⑸

. Tie firmly the rear disc brake clamp and

avoid it to be lifed higher than disc brake oil cup. Disassemble the rear wheel axle at last.

●

Sprocket bracket assembly

  Put down the rear wheel assemble horizontally. Take off nut 

⑾

 with socket sleeve. Take off sprocket 

⑽

; sprocket bracket

⑼

.   Pull out the sprocket gum cushion

⑻

 from the rim.

CAUTION:

●

Use suitable tool to support the motorcycle. Avoid accidents caused by falling motorcycle. Single person manipulation is

prohibited.

●

Using iron hammer to punch rear wheel axle, disc brake clamp assembly is prohibitd.

●

While disassembling the rear wheel assemble, avoid the rear disc brake clamp to be lifted higher than the disc brake oil

cup. If not, air will get into the tubes and cause softness or failure on braking system. As disc brake tubes request extreamly

high vaccum degree. Make sure manipulator has maintenance ability before disassembling the disc brake assembly.

●

All the standard parts need to reach standard torque while reassembling.

●

Check the chain regularly. Clean the chain every 1500km is suggested. Keep the tightness of chain to be in a suitable

range. Too loose chain have possibility to separate from sprocket or damage the engine. Too tight chain can be worn out

quickly.

●

Wheel axle: Use dial indicator to check if it's deformed or bended.

Содержание ZT250-R













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды