manualshive.com logo in svg

Zontes ZT250-R, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT250-R Скачать руководство пользователя страница 61

8-FUEL TANK COMPONENT

60

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1

1251100-102000 Non-standard bolt M6×16

（

stainless steel

）

6

2

1274100-007000

ZT250-S Flanged Bushing (φ6.4×φ9×6

＋

φ20×2)

6

3

1244100-004000 ZT250

－

S Flanged bushing buffer

6

4

1251300-063093 Plywood M6×11×15

（

environmental color

）

2

5

1210141-001000 ZT250

－

S Fuel tank sticker

2

for after-sale

4044101-002036 ZT250

－

R right tank cover (electroplated bright gray

highlight)

【

1

】

4044101-002021 ZT250

－

R right tank cover (special black)

special black

4044100-011036 ZT250

－

S fuel tank right decorative cover

【

1

】

4044100-011021

ZT250

－

S fuel tank right decorative cover (special black)

special black

8

1251200-033093 Non-standard tapping screw ST4.2×12

6

4044101-001036

ZT250

－

R left tank cover (electroplated bright gray highlight)

【

1

】

4044101-001021 ZT250

－

R left tank cover (special black)

special black

4044100-013036

   

gray highlight)

【

1

】

4044100-013021

ZT250

－

S fuel tank left decorative cover (special black)

special black

11

1184200-053000 ZT310PKE external single antenna

1

Old

FIG.4 FUEL TANK

COVER

Fuel tank left and right cover assembly

1

7

10

1

1

9

1

6

PROCEDURE:

●

Fuel tank left and right cover assembly

Remove the bolt (1), bushing (2), buffer rubber (3) and plywood (4) with the hexagonal tool.  Remove the fuel tank left and

right cover assembly.

●

Disassemble fuel tank left cover assembly

Remove the screw (8) with the hexagonal tool, remove the left side cover decorative cover (10), and the left Fuel tank

cover (9).

●

Disassemble fuel tank right cover assembly

Remove the screw (8) with the hexagonal tool, remove the right side cover decorative cover (7), and the left Fuel tank

cover (6).

●

PKE antenna

Remove the PKE external antenna from the upper part of the left cover of the fuel tank.Use a hot air gun to heat up a bit,

remove the double-sided glue 

，

 and clean the residual glue.

●

Fuel tank sticker

If the Fuel tank sticker needs to be replaced with a hot air gun or a hair dryer, it can be moved back and heated and then torn

off. The fuel tank sticker can be purchased separately as an optional part. Crude fuel tank left and right Fuel tank covers
already contain this sticker

CAUTION:

●

The paint surface should be protected when disassembling, pay attention to strength.

●

The torque of the tapping screw should not be too large during reassembly to prevent damage to the Fuel tank cover.

●【

1

】

 use for bright orange /bright blue /dark bright  gray vehicle.

Содержание ZT250-R













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды