Zontes ZT250-R Скачать руководство пользователя страница 66

Страница: 66 / 76

10-REAR COVER COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1224100-052000 ZT250

－

R Electrical device box cover

1244100-072000 ZT250

－

R Battery straps

1224100-051000 Grade 0 flame retardant tie (black 2.5×100)

1184100-116000 ZT250 lithium battery

1240100-023000 Battery anode protection glue

1274200-078000 ZT310

－

R bike tools

1251100-102000 Non

－

standard bolt M6×16(304 stainless steel)

1184200-024000 ZT310

－

R relay of side support

1050953-026000 MT05.2 engine controller

－

ZT250

－

RC4 type

1184100-017000 ZT250

－

S Electric inject relay

1184100-010000 ZT250

－

S Starting relay

PROCEDURE

：

●

Electrical device box cover

Pull the metal buckle of the electrical device box cover (1) in the direction of the arrow, pull it down,

remove it.

●

Battery straps, vehicle tools

Remove the battery strap

⑵

,then remove the vehicle tool

⑹

●

Battery anode protection glue

Find the slotted part of the protective glue

⑸

, use a tool to spread the slot.

●

Battery

Cut the tie

⑶

. Remove the black protective cap

②

Remove the negative pole; then remove the red protective cap

①

Remove the positive pole; Remove the lithium battery

⑷

. When reinstalling, connect the positive pole first,

then the negative pole. Be sure to use a dedicated lithium battery charger for charging. In the event of a power
failure, it is strictly forbidden to bridge or directly connect to the power supply.

●

Relay

Pull out the starting relay

⑾

upwards, open the protective cap and loosen the nut to remove the relay; pull out

the cables of the EFI relay

⑽

and the side bracket relay

⑻

and then pull out

●

Engine controller (ECU)

Remove the bolt

⑺

, pull out the ECU

⑼

and the cable together, and then unplug the ECU plug

●

Fuse box

Pull out the fuse box and cables together, then pinch both ends of the fuse box by hand and open the cover to

replace the fuse

CAUTION:

●

Attention should be paid to the discomponent process to avoid damaging the material. Attention must be paid

to the installation sequence when removing the battery.

●

The battery voltage should be checked regularly. If it is lower than 12.8V, it is recommended to charge it in

time; it must not be overcharged; it should be taken out of storage for a long time without being used, and it
should be charged once a month.

●

Reassemble the battery or fuse, etc. Remember to remember to reset the EFI hardware: Turn on the key-

Ignition- 10 seconds After the ignition is turned off - After 10 seconds Turn on the ignition switch and repeat 2
times.

●

If the battery has reached the end of its useful life, it should be handed over to a qualified organization or a

dedicated recycling center for proper disposal. Discard it at will.

●

EFI relay model: KH-1A4T. Side bracket relay model: G8HN-1C4T-RJ.

FIG.3 REAR COVER

COMPONENT

Battery

、

Electrical device box cover

、

ECU

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды