manualshive.com logo in svg

Zontes ZT250-R, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT250-R Скачать руководство пользователя страница 65

10-REAR COVER COMPONENT

64

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1

1224100-010000 ZT250

－

S Expansion nail

4

2

1251100-101000 Non-standard bolt M6×12 (304 stainless steel)

3

4044101-006033 ZT250

－

R rear   left  cover (bright orange)

1

orange

4044101-006064 ZT250

－

R rear   left  cover (bright blue)

1

blue

4044101-006021 ZT250

－

R rear left decorative cover (special black)

1

gray

4044101-006036 ZT250

－

R rear left decorative cover (electroplated

bright gray highlights)

1

special black

4

1244100-002000 ZT250

－

S Side cover round rubber

4

5

1251200-033093 Non-standard self-tapping screw ST4.2×12

2

4044101-007033

ZT250

－

R right decorative cover of rear cover(bright orange)

1

orange

4044101-007064

ZT250

－

R right decorative cover of of rear cover (bright blue)

1

blue

4044101-007021 ZT250

－

R rear right decorative cover (special black)

1

gray

4044101-007036 ZT250

－

R rear right decorative cover (electroplated

bright gray highlights)

1

special black

7

1210341-001000 ZT250

－

R Rear cover sticker

2

4044100-001036

Rear right side cover(electroplated bright gray highlights)

1

【

1

】

4044100-001021 ZT250

－

S rear  cover right (special black)

1

special black

9

1251300-063093 Plywood M6×11×15

（

environmental color

）

2

10

1174100-007000 ZT250

－

S Rear tail light

1

4044100-003036

Rear  left side cover(electroplated bright gray highlights)

1

【

2

】

4044100-003021 ZT250

－

S rear  left cover  (special black)

1

special black

●

Sticker

The trim cover of rear cover already contains the rear cover stickers, if you need to replace it, you can buy

another one on Zontes official website.

CAUTION:

●

Be sure to fix the motorcycle during discomponent.

●

Pay attention to the discomponent process to avoid damaging the material.

●【

1

】、【

2

】

are used for orange /bright blue/dark blue vehicle.

PROCEDURE:

●

Rear cover component

Remove the four expansion nails (1), remove the three bolts (2) with the hexaongal tool, and pull the front end of

the rear cover off the frame.
   Locate and unplug the cable connector of the rear taillight, grasp the rear taillight 

⑽

 and push the left tail skirt

assembly back and take it off. Similarly, remove the right tail skirt assembly and remove the rear taillight 

⑽

.

Separate the PKE short antenna head from the right tail skirt. Tear off the double-sided tape after heating it with a

heat gun, and clean up the remaining adhesive. The PKE antenna is a  double-sided adhesive glued on the

right tail skirt.

   Remove the bolt (5) of the left rear cover assembly, and force the left trim cover (3) and the left rear cover (11)

apart, remove the round rubber (4) and the plywood (9).

   Similarly remove the right trim cover (6) and the right rear cover (8).

8

11

6

FIG.2 REAR COVER

COMPONENT

Rear skirt 

、

rear light component

3

Содержание ZT250-R













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды