Zontes ZT250-R Скачать руководство пользователя страница 27

Страница: 27 / 76

4-REAR FORKLIFT COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-102000 Non-standard bolts M6c×16 (304 stainless steel)

3070100-008600 Fully synthetic brake oil DOT4 (1L bottle)

【

】

PROCEDURE:

●

Add the brake liquid

Remove the bolts with the inner hex tool

⑴

Pull out the oil cup

④

Should always remain above the line a, parallel to the ground, to prevent the gas from

entering the oil road to cause brake failure.
Remove the bolts with the phillips screwdriver

①

Remove the oil lid

②

seal the rubber pad

③

The top end of the oil cup

④

is basically parallel to the ground, adding DOT4 brake fluid; Make sure the liquid

level is between "UPPER" and" LOWER".

Reset

Step on the brake pedal continuously and make sure that the motorcycle can be driven when the brake is back

to normal.

CAUTION:

●

The motorcycle level should be fixed and checked.

●

Periodically check whether the liquid level of the brake fluid is between "UPPER" and "LOWER".

●

If the liquid level is below "LOWER", check the brake disc wear condition and the brake system leakage first.

●

If swallowed brake fluid, the poison control center or hospital should be contacted immediately; If eye contact,

apply clean water and seek medical treatment immediately.

●

Keep the brake fluid away from children and pets.

●

Do not flush the oil cup directly with high pressure water.

●

It is strictly prohibited to mix water, dust, impurities and liquids of silicic acid or petroleum systems, otherwise

it will cause serious damage to the braking system.

●【

】

Each bottle is 1 liter. It must be used in time after opening, and sealed and moisture-proof measures

must be taken when storing; it is recommended not to exceed 1 month. Inferior or damp brake fluid will cause

adverse effects on the braking system, and may cause brake failure when the impact is severe. Be sure to change

the brake fluid at a maintenance shop with brake fluid replacement equipment and technology to avoid air

entering the brake pipeline.

FIG.11 REAR FORKLIFT

COMPONENT

Add the brake oil to the main pump or rear brake

Front

The back

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды